A 4-layer board that gives a computer its own phone line: LTE data, SMS and voice
calls, with the call audio on USB. Plug in a nano-SIM and one USB-C cable, and the
computer can answer a call through your headset, hand it to a script or an AI agent,
or send a text.
The board was designed by Koppar from a one-page
spec (spec.txt), then reviewed part by part against the datasheets.
Built and tested
Rev B has been manufactured and assembled, and the assembled boards have been brought
up on the bench.
| Assembled boards and bare PCBs from the same batch |
The back |
 |
 |
What has been tested on an assembled board (all results):
- Power: 5 V in over USB-C, the 3.3 V rail, and the 3.8 V buck for the module (3.90 V with no load, inside the module's 3.3 to 4.3 V range).
- USB: the on-board hub at 480 Mb/s, the RP2040 behind it, its flash and its 12 MHz crystal.
- The module's controls: the PWRKEY and RESET_N transistors switch, and the NET, RING and CALL LEDs light.
- The firmware: the RP2040 runs as a USB sound card on the computer. A test tone and a loopback come back at the expected level, the audio streams reopen reliably, and the firmware updates itself over USB.
Not yet tested: everything that needs the Quectel EC25-EUX. The module has been
ordered. Once it is fitted, the next results are the 1.8 V side, the SIM, the
antennas, then the first call, text and data connection. They will be added here.
The boards of this first order have no recovery pads on the back
(see below); the design files have them.
What it does
One USB-C cable, and the computer sees three ordinary devices through the on-board USB hub:
| Device |
From |
For |
| Network adapter |
Quectel EC25-EUX (U8) |
LTE data, with 3G and 2G fallback (European bands) |
| Serial ports |
EC25-EUX |
AT commands: caller ID (+CLIP), texts (AT+CMGS), answer (ATA) |
| USB sound card |
RP2040 (U5) |
Call audio: the module's 1.8 V PCM interface, level-shifted, as a USB microphone and speaker |
There is no battery, screen or speaker. Three LEDs show NET (green), RING (amber) and
CALL (blue). Power is 5 V from USB-C, a 3.8 V / 3 A buck for the module's 2 A
transmit bursts, and 3.3 V for the hub, the RP2040 and its flash.
| Top |
Back |
 |
 |
The schematic is also in PDF.
What is here
| Path |
What it is |
spec.txt |
The spec the board was designed from. |
board/ |
KiCad 10 project: schematic, board, rules, the module footprint, symbol and 3D model. |
board/fab/ |
Gerbers and drill files (gerbers.zip), IPC-2581, schematic PDF. |
board/fab/jlc/ |
JLCPCB assembly BOM and placement files, with the part choices checked by hand. |
REVIEW.md |
The design review: what passed, what changed and why, ordering notes, what is still open. |
firmware/ |
RP2040 firmware: bringup/ (board test) and modem/ (USB sound card for calls, module power, LEDs). |
host/ |
koppar-lte-modem: command line, event daemon and Python API for the computer. |
Build one
Board. Upload board/fab/gerbers.zip to JLCPCB: 4 layers, 1.6 mm, stackup
JLC04161H-3313 (the antenna feeds are 49 Ω on it). Every via is 0.45 / 0.2 mm and
none sits in a pad, so pick Min via hole size 0.2mm/(0.3/0.35mm) and Via covering:
Plugged: no via-in-pad, no extra options.
Assembly. Use board/fab/jlc/BOM-JLCPCB.csv and CPL-JLCPCB.csv. Glance at the
placement preview before confirming, especially the LEDs and the SIM socket
(the card slot is at the board edge). REVIEW.md
lists the parts the files correct.
Parts you source yourself. These are not on JLCPCB's assembly line, or are not on the board at all:
| Part |
What to get |
Where |
| U8, the LTE module |
Quectel EC25-EUX, ordering code EC25EUXGR-128-SGNS (EC25EUXGA-128-SGNS is end-of-life; same LGA-144 footprint). It must be the EUX: the North American data-only variants have no voice. |
Techship, DigiKey, Octopart (stock changes, check the suffix). Deselect U8 at assembly and solder it with hot air or a stencil, or consign it. |
| 2 antennas |
LTE, 698 to 2690 MHz, U.FL (I-PEX MHF I), 50 Ω: one on MAIN (J3), one on DIV (J4) |
e.g. Taoglas FXUB63 or Taoglas FXUB62.07.0150C |
| SIM |
A nano-SIM with a voice plan |
Your carrier |
| Cable and port |
USB-C on both ends, from a port that offers 3 A at 5 V |
The 5.1 kΩ CC resistors make the board a sink; they negotiate nothing, so a USB-A port or a 1.5 A source will brown out in a 2G burst |
Open it in KiCad
Open board/koppar-lte-modem.kicad_pro in KiCad 10. The module's footprint, symbol
and 3D model are in the project (board/footprints, board/custom_syms,
board/models), wired in by the project's library tables.
KiCad's library has no 3D model for two of the footprints, so the 3D viewer shows
them without a body:
| Part |
Footprint |
3D model |
| J1, USB-C receptacle |
Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 |
LCSC C165948 (EasyEDA model) |
| J2, nano-SIM socket |
Connector_JAE:JAE_SIM_Card_SF72S006 |
LCSC C2977286 (EasyEDA model) |
easyeda2kicad converts either one to a
.wrl you can attach to the footprint. The renders above use them.
Bring-up and recovery
There is no BOOTSEL button. A blank RP2040 boots into its USB bootloader anyway, and
the back has three labelled pad groups for the rest:
- BOOT + GND: short them while plugging in and the RP2040 comes up as a USB drive for a new
.uf2, even after a firmware that crashes before USB starts.
- SWD (CLK, DIO, GND): a Pico Debug Probe or any CMSIS-DAP probe.
- USB_BOOT + 1V8: short them while plugging in and the EC25 starts in emergency download mode, for a modem update that went wrong.
Boards from the first rev B order were made from an earlier export and have none
of these pads. To force the RP2040's bootloader on one, bridge pins 1 (CS) and 4
(GND) of the flash, U6, while plugging in (a 1 kΩ resistor's legs, or tweezers),
then let go.
The modem does not switch itself on: the RP2040 drives its PWRKEY (GPIO22) and
RESET_N (GPIO23). Until the firmware runs, the computer sees only the hub and the
RP2040.
The design review
The first version (rev A) had an antenna feed at 35 Ω that hopped
layers, a buck 60 mm from its inductor, and a SIM socket facing the wrong way. All
three are fixed here, along with the parts list and the assembly rotations.
REVIEW.md has every finding with its numbers.
Status
| Board |
Rev B: 0 DRC errors, 0 unconnected, KiCad 10. Built; bring-up without the module passed (results). |
| Firmware |
USB sound card verified on the board (loopback, test tone, repeated stream open/close). Module control written, untested until the EC25 is fitted. |
| Next |
The EC25-EUX is on order. Then: koppar-lte-modem setup, the first call and text. |
VoLTE is optional on the EC25-EUX. Where 2G and 3G are switched off, calls need a
module firmware with VoLTE and a carrier that allows it; ask the seller.
Design your own
This board started as a page of text. Koppar takes a
spec like spec.txt to a schematic, a routed board, a BOM at live prices
and Gerbers. It also takes a KiCad board you already have, or works from your own
agent over MCP.
Licence
CERN Open Hardware Licence Version 2, Permissive (LICENSE).